Location: Cotton Ginning ResearchTitle: Combined lint cleaning system PM2.5 emission factors and rates for cotton gins: Method 201A combination PM10 and PM2.5 sizing cyclones) Author
Submitted to: Journal of Cotton Science
Publication Type: Peer Reviewed Journal
Publication Acceptance Date: 6/21/2013
Publication Date: 12/30/2013
Publication URL: http://handle.nal.usda.gov/10113/5425111
Citation: Buser, M.D., Whitelock, D.P., Boykin Jr, J.C., Holt, G.A. 2013. Combined lint cleaning system PM2.5 emission factors and rates for cotton gins: Method 201A combination PM10 and PM2.5 sizing cyclones. Journal of Cotton Science. 17(4):391-401. Interpretive Summary: In 2006, the US Environmental Protection Agency implemented a more stringent air quality standard for very fine dust smaller than 2.5 micrometers in diameter. All cotton gins will eventually be impacted by this standard. The primary issue affecting the cotton industry across the country is that cotton gins may not be regulated fairly, because very little scientifically sound information is available on cotton gin emissions of this very fine dust. In response, seven cotton gins at locations across the Cotton Belt were sampled by the three USDA-ARS Cotton Ginning Laboratories and Oklahoma State University to determine the amount of very fine dust emitted while processing cotton. Three of the seven gins had combined first and second stage lint cleaning systems. It was found that the combined lint cleaning systems at the gins sampled emitted on average 0.030 pounds of the fine dust for every 500-pound bale of cotton produced, which was about 6% of the total dust emitted from the system. This information provides previously unavailable estimates for fine dust emissions from cotton gins and, thus, will ensure that cotton gins are appropriately permitted and accounted for in state and federal regulations. Furthermore, this may allowing many gins to avoid installing additional dust control measures with substantially higher capital and operating costs that will impact the ginning cost to the farmer.
Technical Abstract: This report is part of a project to characterize cotton gin emissions from the standpoint of stack sampling. In 2006, EPA finalized and published a more stringent standard for particulate matter with nominal diameter less than or equal to 2.5 µm (PM2.5). This created an urgent need to collect additional cotton gin emissions data to address current regulatory issues, because current EPA AP-42 cotton gin PM2.5 emission factors did not exist. The objective of this study was the development of PM2.5 emission factors for cotton gin combined lint cleaning systems based on the EPA-approved stack sampling methodology, Method 201A. The project plan included sampling seven cotton gins across the cotton belt. Key factors for selecting specific cotton gins included: 1) facility location (geographically diverse), 2) industry representative production capacity, 3) typical processing systems, and 4) equipped with properly designed and maintained 1D3D cyclones. Three of the seven gins had 1st and 2nd stage lint cleaning systems where the exhaust airstreams were combined. In terms of capacity, the three gins were typical of the industry, averaging 33.6 bales/h during testing. Some test runs were excluded from the test averages because they failed to meet EPA Method 201A test criteria. Also, other test runs included in the analyses had cotton lint fibers that collected in the = 10 µm and/or = 2.5 µm samples. This larger lint material can impact the reported emissions data, but EPA Method 201A does not suggest methods to account for these anomalies. Average measured combined lint cleaning system PM2.5 emission factor based on the three tests (nine total test runs) was 0.014 kg/227-kg bale (0.030 lb/500-lb bale). The combined lint cleaning system average emission factors for PM10 and total particulate were 0.128 kg/bale (0.281 lb/bale) and 0.233 kg/bale (0.513 lb/bale), respectively. The combined lint cleaning system PM2.5 emission rate from test averages ranged from 0.17 to 0.80 kg/h (0.37-1.75 lb/h). System average PM10 emission factors were higher and system average total particulate emission factors were lower than those currently published in EPA AP-42. The ratios of combined lint cleaning system PM2.5 to total particulate, PM2.5 to PM10, and PM10 to total particulate were 5.9, 10.8, and 54.8%, respectively.