Page Banner

United States Department of Agriculture

Agricultural Research Service

Research Project: ENHANCING QUALITY, UTILITY, SUSTAINABILITY, ENVIRONMENTAL IMPACT OF COTTON AND ITS BYPRODUCTS THROUGH IMPROVEMENT IN HARVEST/GIN PROCESSING

Location: Cotton Ginning Research

Title: Mote cyclone robber system PM2.5 emission factors and rates for cotton gins: Method 201A combination PM10 and PM2.5 sizing cyclones

Authors
item Buser, Michael -
item Whitelock, Derek
item Boykin, J
item Holt, Gregory

Submitted to: Journal of Cotton Science
Publication Type: Peer Reviewed Journal
Publication Acceptance Date: June 21, 2013
Publication Date: December 30, 2013
Citation: Buser, M.D., Whitelock, D.P., Boykin Jr, J.C., Holt, G.A. 2013. Mote cyclone robber system PM2.5 emission factors and rates for cotton gins: Method 201A combination PM10 and PM2.5 sizing cyclones. Journal of Cotton Science. 17(4):468-478.

Interpretive Summary: In 2006, the US Environmental Protection Agency implemented a more stringent air quality standard for very fine dust smaller than 2.5 micrometers in diameter. All cotton gins will eventually be impacted by this standard. The primary issue affecting the cotton industry across the country is that cotton gins may not be regulated fairly, because very little scientifically sound information is available on cotton gin emissions of this very fine dust. In response, seven cotton gins at locations across the Cotton Belt were sampled by the three USDA-ARS Cotton Ginning Laboratories and Oklahoma State University to determine the amount of very fine dust emitted while processing cotton. Three of the seven gins had mote cyclone robber systems. It was found that the mote cyclone robber systems at the gins sampled emitted on average 0.010 pounds of the fine dust for every 500-pound bale of cotton produced, which was about 11% of the total dust emitted from the system. This information provides previously unavailable estimates for fine dust emissions from cotton gins and, thus, will ensure that cotton gins are appropriately permitted and accounted for in state and federal regulations. Furthermore, this may allowing many gins to avoid installing additional dust control measures with substantially higher capital and operating costs that will impact the ginning cost to the farmer.

Technical Abstract: This manuscript is part of a series of manuscripts that detail a project to characterize cotton gin emissions from the standpoint of stack and ambient sampling. The impetus behind the project was the 2006 EPA implementation of a more stringent standard for particulate matter less than or equal to 2.5 micrometers (PM2.5) and the fact that there was very little available cotton gin PM2.5 emissions data. The objective for this study was the development of PM2.5 emission factors for cotton gin mote cyclone robber systems based on the EPA-approved stack sampling methodology, Other Test Method 27. The project plan included sampling seven cotton gins across the Cotton Belt. Key factors for selecting specific cotton gins included: 1) facility location (geographically diverse), 2) industry representative production capacity, 3) typical processing systems, and 4) equipped with properly designed and maintained 1D3D cyclones. Three of the seven gins had mote cyclone robber systems. In terms of capacity, the three gins were typical of the industry, averaging 21.6 bales/hr during testing. Average measured PM2.5 emission factor based on the three tests (5 total test runs) was 0.004 kg/bale (0.010 lb/bale). The project emission factors for PM10 and total particulate were 0.008 kg/bale (0.018 lb/bale) and 0.040 kg/bale (0.089 lb/bale), respectively. The PM2.5 emission rate from test averages ranged from 0.04 to 0.24 kg/hr (0.08 to 0.53 lb/hr). The ratios of PM2.5 to total particulate, PM2.5 to PM10, and PM10 to total particulate were 10.9, 54.4, and 20.1%, respectively.

Last Modified: 4/20/2014
Footer Content Back to Top of Page